Mobil DTE™ 20 Series oils are high performance anti-wear hydraulic oils.
They meet the stringent requirements of hydraulic systems using high pressure, high output pumps as well as other hydraulic system components such as close clearance servo-valves and numerically controlled (NC) machine tools.
These products met the most rigorous performance requirements of a wide range of hydraulic system and component manufacturers, allowing use of a single product with excellent performance characteristics.
Excellent oxidation stability helps reduce maintenance downtime and costs by contributing to system cleanliness and deposit reduction, enable long oil and filter life
Enhanced anti-wear and corrosion protection of system components using various metallurgy help extend component life and improve production capacity
Controlled demulsibility protects systems from small and large quantities of water
Keep clean properties reduce system deposits and sludge help protect equipment and extend equipment life, reduce maintenance costs and improve total system performance
Quality reserve maintains performance features even under severe service conditions and extended drain intervals
Hydraulic systems critical to deposit build-up or where sludge and deposits form with conventional products
Hydraulic systems requiring a high load-carrying capability and anti-wear protection, and when thin oil-film corrosion protection is an asset
Where small amounts of water are unavoidable
Systems containing gears and bearings
Machines employing a wide range of components using various metallurgy
|Mobil DTE 20 Series meets or exceeds the requirements of:||MOBIL DTE 22||MOBIL DTE 24||MOBIL DTE 25||MOBIL DTE 26||MOBIL DTE 27|
|DIN 51524-2: 2006-09||X||X||X||X|
|Mobil DTE 20 Series has the following builder approvals:||MOBIL DTE 22||MOBIL DTE 24||MOBIL DTE 25||MOBIL DTE 26||MOBIL DTE 27|
|HUSKY HS 207||X|
|MOBIL DTE 21||MOBIL DTE 22||MOBIL DTE 24||MOBIL DTE 25||MOBIL DTE 26||MOBIL DTE 27||MOBIL DTE 28|
|Viscosity, ASTM D445|
|cSt @ 100°C||2.7||4.5||5.3||6.7||8.5||10.9||14.3|
|cSt @ 40°C||10||21||31.5||44.2||71.2||95.3||142.8|
|Viscosity Index, ASTM D2270||98||98||98||98||98||98||98|
|Pour Point, °C, ASTM D97||-30||-30||-27||-27||-21||-21||-15|
|Flash Point, COC, ASTM D92||174||200||220||232||236||248||276|
|Foam, Seq I, Tendency/Stability, ASTM D892||20/0||20/0||20/0||20/0||20/0||20/0||20/0|
|Foam, Seq II, Tendency/Stability, ASTM D892||20/0||20/0||20/0||20/0||20/0||20/0||20/0|
|Foam, Seq III, Tendency/Stability, ASTM D892||20/0||20/0||20/0||20/0||20/0||20/0||20/0|
|Copper strip corrosion, 3 hrs @ 100°C, ASTM D130||1B||1B||1B||1B||1B||1B||1B|
|Rust protection Proc B, ASTM D665||PASS||PASS||PASS||PASS||PASS||PASS||PASS|
|****FZG Failure Load Stage, ISO 14635-1(mod)||12||12||12||12||12|
Health and Safety recommendations for this product can be found on the Material Safety Data Sheet (MSDS) @http://www.msds.exxonmobil.com/psims/psims.aspx
All trademarks used herein are trademarks or registered trademarks of Exxon Mobil Corporation or one of its subsidiaries unless indicated otherwise.